Cold Shuts

Started by Fulvio, June 26, 2013, 09:47:49 PM

Previous topic - Next topic

0 Members and 0 Guests are viewing this topic.

Robster

Great lamination Unicorn, if I ever get through the pre-decimals I look forward to the "new" coins.!! :angel:
\"Everything in moderation, including moderation\".

Nevol

Fulvio, Do the cold shuts always have the curled bit at the narrow end or would/could this be one?

From memory, nearly all the ones I have are like this, maybe only a couple with the curl.

50c 2005 CG Obv Cold Shut @ 6k
A Platypus is a duck designed by a committee ( anon)

Nevol

These are what I believe, are the majority of my other Cold Shut coins that I can find.  I have more 50c Rev ones, but their whereabouts elude me at present.

$1 1984 Obv Cold Shut @ 4-5k.jpg


$2 2003 Obv Cold Shut @ 4-5.30k.jpg


$2 2006 Obv Cold Shut @ 11-12k.jpg


10c 2006 Rev Cold Shut @ 6k.jpg


10c 2006 Rev Cold Shut @ 7k.jpg


5c 1988 Obv Cold Shut @ 11k.jpg


5c 2001 Rev Cold Shut @ 12 - 1.30k.jpg


5c 2006 Rev Cold Shut @ 12.30k.jpg
A Platypus is a duck designed by a committee ( anon)

ausjack

they look sort of like a tear..very funny and nice pic's Nevol :good:
A wise person knows there is something to learn from everyone.

Fulvio

Quote from: 'markn' pid='19651' dateline='1372375414'Sorry if this is unclear but it's been a while since I did any metallurgy.

No, its crystal clear. And makes a lot of sense too. Thanks.

OK, I'll change my stance now, especially after seeing that lovely 2008 $1. Clearly while the processes have improved, there is still the occasional oopsie. :dodgy:

Quote from: 'Nevol' pid='19689' dateline='1372386198'Fulvio, Do the cold shuts always have the curled bit at the narrow end or would/could this be one?

Nope. they're almost always just like the one in your pic.

Quote from: 'Nevol' pid='19718' dateline='1372394187'5c 1988 Obv Cold Shut @ 11k.jpg

I especially like that one. Looks like a tail. Critter must be hiding on the Rev, eh?
http://fulvio55.altervista.org/ - Decimal Mintages and Polymer Notes PDFs
Doge: DG8r9JJnWCHVvd1iG4BJeJMj5g1reYTnSc - BTC: 1FFnNxMDNCnQEjHrh9EhnHZoDMjkbf1seW

Unicorn

Quotethat lovely 2008 $1

While the topic is still hot, a couple more ....

2005 Dancing Man



2006 MOR


Fulvio

Quote from: 'Unicorn' pid='19738' dateline='1372397690'While the topic is still hot, a couple more ....

OK, rub it in, why don't ya.. lovely coins though.. What was your address again? :diablo:
http://fulvio55.altervista.org/ - Decimal Mintages and Polymer Notes PDFs
Doge: DG8r9JJnWCHVvd1iG4BJeJMj5g1reYTnSc - BTC: 1FFnNxMDNCnQEjHrh9EhnHZoDMjkbf1seW

Fulvio

Since having a discussion with Goldy, and slobbering all over a couple of lovely lamination flaws, I've been wondering about something..

Are ALL planchet flaws actually Cold Shuts?

There are a number of different types of metal defects, but to me it seems most of them don't apply to the rolled alloys our coins are made from. Shrinkage, Gas Porosity, Inclusions and Metallurgical Defects are more applicable to castings than rolled metals, whereas the rolling process itself appears to have a tendency to promote cold shuts.

If this theory is correct, then the different types of flaws, ranging from rim flakes to tears across the face of a coin to sections falling out to planchet splits, are all about the size and placement of the shut in relation to the planchet stamped through it. As with cuds and cracks, which vary from minute to colossal, its just a matter of degree.
http://fulvio55.altervista.org/ - Decimal Mintages and Polymer Notes PDFs
Doge: DG8r9JJnWCHVvd1iG4BJeJMj5g1reYTnSc - BTC: 1FFnNxMDNCnQEjHrh9EhnHZoDMjkbf1seW

trout

From what I can understand is that Gold is one of the only metals that can be "Rolled" without any perceptible defects as it is a relatively soft metal.
Once you start using the same process with harder metals , ANY defect or dent in the ingot to be rolled will be transferred to the sheet when rolled .
The planchet peels could be simply a bit of metal that was folded over in the rolling process and ended up not unlike the way puff pastry is produced :ok:
Aim well to enjoy life. You only get One shot at it.
Illegitimi non carborundum

JeffH

I'm thinking this could be a cold shut. Looks like a planchet flaw anyway -not PMD?

Taken with my digital microscope; now mounted on my new stand.
Thinking is dangerous, it makes you think. That\'s why many people avoid it.

Robster

\"Everything in moderation, including moderation\".

Fulvio

Quote from: 'JeffH' pid='32055' dateline='1382561225'I'm thinking this could be a cold shut.

Yup. Definitely not PMD.

As I said a while ago, I've come to the conclusion that planchet flaws are all cold shuts anyway. The different looks are just a matter of how the pieces align. Whether its a long rip or a section that falls out, as this is, its all basically the same.

Your pic also clearly shows the parallel stripes that show up on a lot of this vintage. I think those stripes are a surface indication of flaws underneath. When those flaws come to the surface, they always seem to line up along the stripes. Perhaps the metal is folded in a wave, and the stripes are the tops of those waves? Also why does this only seem to happen with coins from this era? A difference in the planchet materials or manufacture? Or perhaps the stripes are an indication of stresses as the layers begin to separate, and that takes many years? If the latter, we may see the effect on younger coins in future.

It would be interesting to be able to see a cross-section.
http://fulvio55.altervista.org/ - Decimal Mintages and Polymer Notes PDFs
Doge: DG8r9JJnWCHVvd1iG4BJeJMj5g1reYTnSc - BTC: 1FFnNxMDNCnQEjHrh9EhnHZoDMjkbf1seW

JeffH

I would think that stripes are because planchet stock is rolled to thickness uni-directionally.
Thinking is dangerous, it makes you think. That\'s why many people avoid it.