1961 bar in wool shilling

Started by serial, July 11, 2016, 09:38:30 PM

Previous topic - Next topic

0 Members and 0 Guests are viewing this topic.

trout

No luck in the junk buckets finding one of these :(

I have to add however that I really enjoyed handling a bunch of coins without a care about fingerprints or dropping them for once :good:
Aim well to enjoy life. You only get One shot at it.
Illegitimi non carborundum

Fulvio

Quote from: 'nealeffendi' pid='92482' dateline='1468397238'Now if the die had been accidentally damaged (such as getting whacked into by another die when a batch was being annealed) then the defect might be a neat bar.

Yes, but my point was this would then be on the SURFACE of the die, the field of the coin. Or along an edge in the design. Which is where just about all the cuds occur. Actually, other than the 'Uluru' Outback dollars, I'm hard pressed to think of other examples of holes in the design part of a die right now.
http://fulvio55.altervista.org/ - Decimal Mintages and Polymer Notes PDFs
Doge: DG8r9JJnWCHVvd1iG4BJeJMj5g1reYTnSc - BTC: 1FFnNxMDNCnQEjHrh9EhnHZoDMjkbf1seW

nealeffendi

Quote from: 'Fulvio' pid='92526' dateline='1468467348'
Quote from: 'nealeffendi' pid='92482' dateline='1468397238'Now if the die had been accidentally damaged (such as getting whacked into by another die when a batch was being annealed) then the defect might be a neat bar.

Yes, but my point was this would then be on the SURFACE of the die, the field of the coin. Or along an edge in the design. Which is where just about all the cuds occur. Actually, other than the 'Uluru' Outback dollars, I'm hard pressed to think of other examples of holes in the design part of a die right now.

What about the halfpennies of 1921 with the denticle patterns? Might they not also be dents in the die from making contact with another die? Also the 1964? (IIRC) pennies with 1, 2 or 3 denticle patterns. Careless workshop employees when handling dies during hubbing or annealing might cause one hardened die to make a glancing blow against another softer die and leave a ding. Especially easy to do when trying to manipulate very hot dies with tongs and heavy gauntlets.
I also have seen 1920 pennies with faults that represent damaged dies (most likely due to a tool or other hard piece of metal whacking the die).

Fulvio

Quote from: 'nealeffendi' pid='92530' dateline='1468479399'What about the halfpennies of 1921 with the denticle patterns? Might they not also be dents in the die from making contact with another die? Also the 1964? (IIRC) pennies with 1, 2 or 3 denticle patterns. Careless workshop employees when handling dies during hubbing or annealing might cause one hardened die to make a glancing blow against another softer die and leave a ding. Especially easy to do when trying to manipulate very hot dies with tongs and heavy gauntlets.
I also have seen 1920 pennies with faults that represent damaged dies (most likely due to a tool or other hard piece of metal whacking the die).

Not really being a predecimal collector, I'm afraid I'm unfamiliar with those particular coins. Pictures?

However, in general terms, sure, impact damage occurs all the time. But whether its a die clash, dropped tool, careless cleaning or whatever, it mostly affects the high parts of the die, which is the field of the coin, or the edges of the design. For something to reach down into a crevice with enough force to leave a mark such as we're discussing, even with soft metal, well, I'm having a hard time explaining that.
http://fulvio55.altervista.org/ - Decimal Mintages and Polymer Notes PDFs
Doge: DG8r9JJnWCHVvd1iG4BJeJMj5g1reYTnSc - BTC: 1FFnNxMDNCnQEjHrh9EhnHZoDMjkbf1seW