Possible 2014 $1 Mule

Started by Bigfellani5, August 26, 2016, 10:46:06 AM

Previous topic - Next topic

0 Members and 0 Guests are viewing this topic.

trout

Is there any more news on this coin or has anyone else found another one yet ??
Aim well to enjoy life. You only get One shot at it.
Illegitimi non carborundum

Bigfellani5

My customer contacted yesterday. I will have the coin back to scan again late next week. Will do one with it next to a 2014 10c so some comparisons can be made.

Is there anything else picture wise or measurement wise anyone wants to know so I can make sure I get them when the coin comes back in.

ausjack

Yes please. Maybe besides a 2014 $1 and measure both as well to see if it an over sized planchet.
A wise person knows there is something to learn from everyone.

Unicorn

Yes please also, next to the normal 2014 $1 as AJ mentioned. So just the three all in the same scan. (1) Potential Mule, (2) 2014 10c and (3) normal 2014 Anzac $1.

That would be great.

robbiegal

Quote from: 'ausjack' pid='97323' dateline='1473299944'Yes please. Maybe besides a 2014 $1 and measure both as well to see if it an over sized planchet.

1. weight as the minting process should squish the coin into the correct size (?)

ausjack

Even if weighing it it might still be within the tolerance, maybe.
A wise person knows there is something to learn from everyone.

JeffH

I don't think weight (mass) is relevant. If it is the correct planchet that will also be correct.

To me the best indicator is to actually measure the coin design size -not the overall coin size.
If you have access to a vernier caliper this is a simple exercise.

I just measured a few 2014 $1 and 10¢ coins and have, for the distance between the top of the 'T' in Elizabeth and the top of the 'I' in Australia as;
•$1    -22.0mm
•10¢  -21.1mm
If you measure a normal $1, leave the jaws on the caliper at the same setting and it will be very obvious when you then put it across a mule. Try it with a few normal $1 and 10¢ first and you will see.

Vernier calipers can measure accurately to 0.01mm but, for a host of reasons I will not bother listing here, anything better than 0.05mm is virtually impossible to achieve on a circulated coin. Anyway, to the nearest  0.1mm is more than adequate for this exercise. [Sorry Robbiegal, just ignore all this technical jargon and wait for the end result.]

Take care not to dig the points of the jaw into the coin -don't want to scratch it. And plastic verniers are not very accurate but would be good enough for a comparative exercise like this.

I have just realised that most of you will not have a clue what the measuring tool I mentioned is. This is what it looks like (mine has a red/brown case instead of blue -must submit it to PCGS to see what colour they call it but, maybe, I should talk to trout first to see if they are the best people to determine!)
Thinking is dangerous, it makes you think. That\'s why many people avoid it.

Fulvio

Quote from: 'JeffH' pid='97344' dateline='1473323178'This is what it looks like

20 years ago, yeah. That was when I switched to dial calipers. MUCH easier on the old eyes. ;)
http://fulvio55.altervista.org/ - Decimal Mintages and Polymer Notes PDFs
Doge: DG8r9JJnWCHVvd1iG4BJeJMj5g1reYTnSc - BTC: 1FFnNxMDNCnQEjHrh9EhnHZoDMjkbf1seW

JeffH

Quote20 years ago, yeah.
I bought mine around 1970 and use them regularly. Still accurate and easy to read.
Thinking is dangerous, it makes you think. That\'s why many people avoid it.

ausjack

You must remember Jeff that Fulvio is as old as methuselah so the old eyes aren't quite what they used to be so if the letters aren't 3" high he can't see them...time to go fishing, that should get a good bite :D
A wise person knows there is something to learn from everyone.

robbiegal


Hercules

Quote from: 'Unicorn' pid='97324' dateline='1473301392'So just the three all in the same scan. (1) Potential Mule, (2) 2014 10c and (3) normal 2014 Anzac $1.

I think you should get a regular 2000 mule as well, just for comparison.

Keep in mind that the ANZAC $1 coins span multiple years, so if it is a mule, it could have been minted long after the original run of 2014 ANZAC $1 coins had ended.

Suppose a worker had been told to make a run of 2015 or 2016 ANZAC $1 coins, for either the Changeover Tour or for general circulation, but mistakenly assumed that that would be a mule, so they made a last-minute decision to use a 2014 obverse instead. The 2014 $1 obverses may well have been retired by that stage, in favour of the 2015 or 2016 ones, but with the 2014 10c coins still being minted well into 2015, the dies could have easily been mixed up without anyone noticing. By this stage, the 2014 ANZAC $1 coins would have been relatively common, so no one would have bothered to check them properly. Even if they did, it's hard to deny that a genuine 2014 ANZAC $1 mule looks less like a mule than a regular 2015 ANZAC $1 coin.

Triggersmob

Quote from: 'JeffH' pid='97344' dateline='1473323178'I don't think weight (mass) is relevant. If it is the correct planchet that will also be correct.

To me the best indicator is to actually measure the coin design size -not the overall coin size.
If you have access to a vernier caliper this is a simple exercise.

I just measured a few 2014 $1 and 10¢ coins and have, for the distance between the top of the 'T' in Elizabeth and the top of the 'I' in Australia as;
•$1    -22.0mm
•10¢  -21.1mm
If you measure a normal $1, leave the jaws on the caliper at the same setting and it will be very obvious when you then put it across a mule. Try it with a few normal $1 and 10¢ first and you will see.

Vernier calipers can measure accurately to 0.01mm but, for a host of reasons I will not bother listing here, anything better than 0.05mm is virtually impossible to achieve on a circulated coin. Anyway, to the nearest  0.1mm is more than adequate for this exercise. [Sorry Robbiegal, just ignore all this technical jargon and wait for the end result.]

Take care not to dig the points of the jaw into the coin -don't want to scratch it. And plastic verniers are not very accurate but would be good enough for a comparative exercise like this.


I have just realised that most of you will not have a clue what the measuring tool I mentioned is. This is what it looks like (mine has a red/brown case instead of blue -must submit it to PCGS to see what colour they call it but, maybe, I should talk to trout first to see if they are the best people to determine!)


Mitutoyo, nothing but the best. I have plastic ones I use on coins. Not sure just how accurate they are, but it gives me a guide.
Steve

OFEC count = 258

Fulvio

Quote from: 'Hercules' pid='97379' dateline='1473337595'a genuine 2014 ANZAC $1 mule looks less like a mule than a regular 2015 ANZAC $1 coin.

How on earth would you tell the difference between a 2014 coin minted in 2014 vs one made in any other year???

Personally, I think you're drawing a long bow with that theory.

2014:  60,682,000

Why would they still be making 2014 10¢ a year later when this is the highest mintage since 2010?
http://fulvio55.altervista.org/ - Decimal Mintages and Polymer Notes PDFs
Doge: DG8r9JJnWCHVvd1iG4BJeJMj5g1reYTnSc - BTC: 1FFnNxMDNCnQEjHrh9EhnHZoDMjkbf1seW

ausjack

A wise person knows there is something to learn from everyone.