Show posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - SirDave

#2
Australian Errors and Varieties / RE: Alloy problem?
December 01, 2015, 08:30:05 PM
I was wondering about heat. Sounds like it's likely. Coin looks remarkably good though and the discolouration only shows up in certain light. I might try an experiment with some coins and a flame.
#3
Australian Errors and Varieties / Alloy problem?
November 30, 2015, 10:04:20 PM
Has anyone seen this type of issue before? looks like the alloy isn't quite right? I have heard about this but had't seen it. Can't see any sign of pmd.

The discolouration seems similar to some types of copper toning.

Obverse

Reverse

Side
#4
Australian Decimal NCLT / RE: Legit or not?
November 21, 2015, 07:42:02 AM
Totally agree, absolute fake. Diameter, map outline all wrong.
If I were the mint rep being very diligent in my duties on the stall I would be really annoyed.
It is worth noting though that he did stamp these 'by eye' so the positions do vary slightly on the pre minted coins (not sure i like the idea of a stamp added after the initial minting).
These aren't sealed either and were in the slip in folders.
#5
Quote from: 'kchan1111' pid='80943' dateline='1445514826'
Quote from: 'SirDave' pid='80937' dateline='1445506803'Yay, picked my coins up today from the travelling mint tent!

Trying to work out how to add images again...

SirDave - what are the special items on offer from the travelling tent?

2015 $1 Anzac, $2 orange, $2 red.  (Swap for change)

2015 $1 counterstamp ($10)

Plus other stuff in glass cabinet I didnt really take note of.

Got there late in the day (in the rain) and lines were short. Apparent it was 1hr at lunchtime.
#6
Yay, picked my coins up today from the travelling mint tent!

Trying to work out how to add images again...
#7
Can anyone confirm correct position of this coin. I checked my McDonald's 2012 and it looks upset in the catalogue. I assume windmill vertical and 50 on an angle is correct (as per ones I noodled) the catalogue is offset by one edge.
#8
Gee, nice find Trout, I have always liked that coin since I first held one my friend had. Still haven't picked one up yet.
#9
My first PGCS coin. They are smaller than I imagined! Must say, it's nice to be able to see where it sits in the population of graded coins. I hope I don't get hooked...

http://www.ebay.com.au/itm/1969-20-cent-graded-to-ms-65-/221806618125
#10
Sorry, Trout, I did think you were referring to my mums shilling. I must have missed the 1835 one. I thought maybe my english gas meter provenance might have excluded it!
#11
Why wrong thread? It's a proclamation coin?
#12
Here's one my mum picked up when she worked in a bank in England in the 60s. It came from gas meters where people had coin operated gas at home. People got desperate for heat in the English winters.

It was only when mum got some of her old coins out I realised it was a proclamation coin.

I love this coin, it has a great look and I like the angular reeding these coins have.

To me this looks in pretty good nick.

Reverse
#13
My first 2014 MOR, NCLT RAM.

The Quarter was in an Armaguard $1 roll. I often seem to get duded on the rolls. 5c in the $2 rolls are the worst offenders.



#14
A couple of the photos appear to show solid metal at the base of the cut which could only be from cutting of some sort.

Other parts look consistent with planchet flaw so I agree it iprobably started as a genuine flaw that has been exaggerated by intervention which is a shame.
#15
I might email the mint, perhaps they have a quality control dept that would be interested.